View NLSX3014_4700461.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NLSX3014 4-Bit 100 Mb/s Configurable Dual-Supply Level Translator
The NLSX3014 is a 4-bit configurable dual-supply bidirectional level translator without a direction control pin. The I/O VCC- and I/O VL-ports are designed to track two different power supply rails, VCC and VL respectively. The VCC supply rail is configurable from 1.3 V to 4.5 V while the VL supply rail is configurable from 0.9 V to (VCC - 0.4) V. This allows lower voltage logic signals on the VL side to be translated into higher voltage logic signals on the VCC side, and vice-versa. Both I/O ports are auto-sensing; thus, no direction pin is required. The Output Enable (EN) input, when Low, disables both I/O ports by putting them in 3-state. This significantly reduces the supply currents from both VCC and VL. The EN signal is designed to track VL.
Features http://onsemi.com MARKING DIAGRAM
1 UQFN12 MU SUFFIX CASE 523AE UTMG G
UT = Specific Device Code M = Date Code G = Pb-Free Package (Note: Microdot may be in either location)
LOGIC DIAGRAM
EN VL VCC GND
* Wide High-Side VCC Operating Range: 1.3 V to 4.5 V * * * * * *
Wide Low-Side VL Operating Range: 0.9 V to (VCC - 0.4) V High-Speed with 100 Mb/s Guaranteed Date Rate for VL > 1.6 V Low Bit-to-Bit Skew Overvoltage Tolerant Enable and I/O Pins Non-preferential Powerup Sequencing Small packaging: 1.7 mm x 2.0 mm UQFN12 This is a Pb-Free Device
I/O VL1
I/O VCC1
I/O VL2
I/O VCC2
Typical Applications
* Mobile Phones, PDAs, Other Portable Devices
I/O VL3
I/O VCC3
I/O VL4
I/O VCC4
PIN ASSIGNMENT
EN VL I/O VL1 I/O VL2 I/O VL3 I/O VL4
1 2 3 4 5 6 12 11 10 9 8 7
VCC I/O VCC1 I/O VCC2 I/O VCC3 I/O VCC4
GND (TOP VIEW)
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet.
(c) Semiconductor Components Industries, LLC, 2008
July, 2008 - Rev. 4
1
Publication Order Number: NLSX3014/D
NLSX3014
VL +1.8V +3.6V P One-Shot 4 kW VCC
VL +1.8 V System
NLSX3014
VCC +3.6 V System I/O VL N One-Shot I/O VCC
I/O1 I/On GND EN
I/O VL1
I/O VCC1
I/O1 I/On GND
I/O VLn I/O VCCn EN GND
P One-Shot 4 kW N One-Shot
Figure 1. Typical Application Circuit
Figure 2. Simplified Functional Diagram (1 I/O Line) (EN = 1) FUNCTION TABLE
PIN ASSIGNMENT
Pins VCC VL GND EN I/O VCCn I/O VLn Description VCC Input Voltage VL Input Voltage Ground Output Enable I/O Port, Referenced to VCC I/O Port, Referenced to VL
EN L H
Operating Mode Hi-Z I/O Buses Connected
http://onsemi.com
2
NLSX3014
MAXIMUM RATINGS
Symbol VCC VL I/O VCC I/O VL VEN IIK IOK ICC IL IGND TSTG VCC Supply Voltage VL Supply Voltage VCC-Referenced DC Input/Output Voltage VL-Referenced DC Input/Output Voltage Enable Control Pin DC Input Voltage Input Diode Clamp Current Output Diode Clamp Current DC Supply Current Through VCC DC Supply Current Through VL DC Ground Current Through Ground Pin Storage Temperature Parameter Value -0.5 to +5.5 -0.5 to +5.5 -0.5 to (VCC + 0.3) -0.5 to (VL + 0.3) -0.5 to +5.5 -50 -50 $100 $100 $100 -65 to +150 VI < GND VO < GND Condition Unit V V V V V mA mA mA mA mA C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Symbol VCC VL VEN VIO TA DI/DV VCC Supply Voltage VL Supply Voltage Enable Control Pin Voltage Bus Input/Output Voltage Operating Temperature Range Input Transition Rise or Rate VI, VIO from 30% to 70% of VCC; VCC = 3.3 V $ 0.3 V I/O VCC I/O VL Parameter Min 1.3 0.9 GND GND GND -40 0 Max 4.5 VCC - 0.4 4.5 4.5 4.5 +85 10 Unit V V V V C ns
http://onsemi.com
3
NLSX3014
DC ELECTRICAL CHARACTERISTICS
-405C to +855C Symbol VIHC VILC VIHL VILL VIH VIL VOHC VOLC VOHL VOLL Parameter I/O VCC Input HIGH Voltage I/O VCC Input LOW Voltage I/O VL Input HIGH Voltage I/O VL Input LOW Voltage Control Pin Input HIGH Voltage Control Pin Input LOW Voltage I/O VCC Output HIGH Voltage I/O VCC Output LOW Voltage I/O VL Output HIGH Voltage I/O VL Output LOW Voltage TA = +25C TA = +25C I/O VCC Source Current = 20 mA I/O VCC Sink Current = 20 mA I/O VL Source Current = 20 mA I/O VL Sink Current = 20 mA Test Conditions (Note 1) VCC (V) (Note 2) 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 VL (V) (Note 3) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) Min 0.8 * VCC - 0.8 * VL - 0.8 * VL - 0.8 * VCC - 0.8 * VL - Typ (Note 4) - - - - - - - - - - Max - 0.2 * VCC - 0.2 * VL - 0.2 * VL - 0.2 * VCC - 0.2 * VL Unit V V V V V V V V V V
1. Normal test conditions are VEN = 0 V, CIOVCC = 15 pF and CIOVL = 15 pF, unless otherwise specified. 2. VCC is the supply voltage associated with the high voltage port, and VCC ranges from +1.3 V to 4.5 V under normal operating conditions. 3. VL is the supply voltage associated with the low voltage port. VL must be less than or equal to (VCC - 0.4) V during normal operation. However, during startup and shutdown conditions, VL can be greater than (VCC - 0.4) V. 4. Typical values are for VCC = +2.8 V, VL = +1.8 V and TA = +25C. All units are production tested at TA = +25C. Limits over the operating temperature range are guaranteed by design.
POWER CONSUMPTION
Symbol IQ-VCC IQ-VL Parameter Test Conditions (Note 5) VCC (V) (Note 6) VL (V) (Note 7) -405C to +855C Min - - - Typ - - - Max 1.0 1.0 2.0 Unit mA mA
Supply Current from EN = VL; I/O VCCn = 0 V, I/O VLn = 0 V, 1.3 to 3.6 0.9 to (VCC - 0.4) VCC I/O VCCn = VCC or I/O VLn = VL and Io = 0 Supply Current from EN = VL; I/O VCCn = 0 V, I/O VLn = 0 V, 1.3 to 3.6 0.9 to (VCC - 0.4) VL I/O VCCn = VCC or I/O VLn = VL and Io = 0 EN = VL, I/O VCCn = 0 V, I/O VLn = 0 V, I/O VCCn = VCC or I/O VLn = (VCC - 0.2 V) and Io = 0 < (VCC - 0.2)
ITS-VCC
VCC Tristate Output Mode Supply Current VL Tristate Output Mode Supply Current I/O Tristate Output Mode Leakage Current Output Enable Pin Input Current
EN = 0 V
1.3 to 3.6 0.9 to (VCC - 0.4)
-
-
1.0
mA
ITS-VL
EN = 0 V EN = 0 V EN = 0 V EN = 0 V -
1.3 to 3.6 0.9 to (VCC - 0.4) VCC - 0.2 1.3 to 3.6 0.9 to (VCC - 0.4) VCC - 0.2 1.3 to 3.6 0.9 to (VCC - 0.4)
- - - - -
- - - - -
0.2 2.0 0.15 2.0 1.0
mA
IOZ
mA
IEN
mA
5. Normal test conditions are VEN = 0 V, CIOVCC = 15 pF and CIOVL = 15 pF, unless otherwise specified. 6. VCC is the supply voltage associated with the high voltage port, and VCC ranges from +1.3 V to 3.6 V. 7. VL is the supply voltage associated with the low voltage port. VL must be less than or equal to (VCC - 0.4) V during normal operation. However, during startup and shutdown conditions, VL can be greater than (VCC - 0.4) V.
http://onsemi.com
4
NLSX3014
TIMING CHARACTERISTICS
-405C to +855C Symbol tR-VCC tF-VCC tR-VL tF-VL ZO-VCC ZO-VL Parameter I/O VCC Rise Time (Output = I/O_VCC) I/O VCC Falltime (Output = I/O_VCC) I/O VL Risetime (Output = I/O_VL) I/O VL Falltime (Output = I/O_VL) I/O VCC One-Shot Output Impedance I/O VL One-Shot Output Impedance CIOVCC = 15 pF Test Conditions (Note 8) CIOVCC = 15 pF CIOVCC = 15 pF CIOVL = 15 pF CIOVL = 15 pF VCC (V) (Note 9) 1.3 to 4.5 > 2.0 1.3 to 4.5 > 2.0 1.3 to 4.5 > 2.0 1.3 to 4.5 > 2.0 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 > 2.0 CIOVL = 15 pF 1.3 to 4.5 > 2.0 CIOVCC = 15 pF 1.3 to 4.5 > 2.0 CIOVCC = 15 pF 1.3 to 4.5 > 2.0 (Output = I/O_VCC, CIOVCC = 15 pF) (Output = I/O_VL, CIOVL = 15 pF) 1.3 to 4.5 > 2.0 VL (V) (Note 10) 0.9 to (VCC - 0.4) > 1.6 0.9 to (VCC - 0.4) > 1.6 0.9 to (VCC - 0.4) > 1.6 0.9 to (VCC - 0.4) > 1.6 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) > 1.6 0.9 to (VCC - 0.4) > 1.6 0.9 to (VCC - 0.4) > 1.6 0.9 to (VCC - 0.4) > 1.6 0.9 to (VCC - 0.4) > 1.6 60 100 Min Typ (Note 11) 1.3 0.9 0.8 0.6 2.7 0.8 0.8 0.7 30 30 15 4 10 3 0.6 0.2 0.4 0.2 17 5 11 4 1 0.8 0.6 0.3 Mb/s nS nS ns Max 1.7 1.1 1.2 1.0 3.0 1.0 1.0 0.8 W W ns ns ns ns Unit ns
tPD_VL-VCC Propagation Delay (Output = I/O_VCC, tPHL, tPLH) tPD_VCC-VL Propagation Delay (Output = I/O_VL, tPHL, tPLH) tSK VL-VCC Channel-to-Channel Skew (Output = I/O_VCC)
tSK_VCC-VL Channel-to-Channel Skew (Output = I/O_VL) Maximum Data Rate
8. Normal test conditions are VEN = 0 V, CIOVCC = 15 pF and CIOVL = 15 pF, unless otherwise specified. 9. VCC is the supply voltage associated with the high voltage port, and VCC ranges from +1.3 V to 4.5 V under normal operating conditions. 10. VL is the supply voltage associated with the low voltage port. VL must be less than or equal to (VCC - 0.4) V during normal operation. However, during startup and shutdown conditions, VL can be greater than (VCC - 0.4) V. 11. Typical values are for VCC = +2.8 V, VL = +1.8 V and TA = +25C. All units are production tested at TA = +25C. Limits over the operating temperature range are guaranteed by design.
http://onsemi.com
5
NLSX3014
ENABLE / DISABLE TIME MEASUREMENTS
-405C to +855C Symbol tEN-VCC Parameter Turn-On Enable Time (Output = I/O_VCC, tpZH) Turn-On Enable Time (Output = I/O_VCC, tpZL) tEN-VL Turn-On Enable Time (Output = I/O_VL, tpZH) Turn-On Enable Time (Output = I/O_VL, tpZL) tDIS-VCC Turn-Off Disable Time (Output = I/O_VCC, tpHZ) Propagation Delay (Output = I/O_VCC, tPLZ) tDIS-VL Turn-Off Disable Time (Output = I/O_VL, tpHZ) Propagation Delay (Output = I/O_VL, tPLZ) Test Conditions (Note 12) CIOVCC = 15 pF CIOVL = 15 pF CIOVCC = 15 pF CIOVL = 15 pF CIOVCC = 15 pF CIOVL = 15 pF CIOVCC = 15 pF CIOVL = 15 pF VCC (V) (Note 13) 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 1.3 to 4.5 VL (V) (Note 14) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) 0.9 to (VCC - 0.4) Min Typ (Note 15) 80 175 250 175 90 150 200 150 Max 140 300 475 250 140 200 300 250 Unit ns ns ns ns ns ns ns ns
12. Normal test conditions are VEN = 0 V, CIOVCC = 15 pF and CIOVL = 15 pF, unless otherwise specified. 13. VCC is the supply voltage associated with the high voltage port, and VCC ranges from +1.3 V to 4.5 V under normal operating conditions. 14. VL is the supply voltage associated with the low voltage port. VL must be less than or equal to (VCC - 0.4) V during normal operation. However, during startup and shutdown conditions, VL can be greater than (VCC - 0.4) V. 15. Typical values are for VCC = +2.8 V, VL = +1.8 V and TA = +25 C. All units are production tested at TA = +25 C. Limits over the operating temperature range are guaranteed by design. NLSX3014 EN Source I/O VL I/O VCC CIOVCC I/O VL CIOVL Source I/O VL 90% 50% 10% tPD_VL-VCC I/O VCC 90% 50% 10% tF-VCC tR-VCC tRISE/FALL v 3 ns I/O VCC 90% 50% 10% tPD_VL-VCC tPD_VCC-VL I/O VL 90% 50% 10% tF-VL tR-VL tPD_VCC-VL tRISE/FALL v 3 ns NLSX3014 EN I/O VCC
VL
VCC
VL
VCC
Figure 3. Driving I/O VL Test Circuit and Timing
Figure 4. Driving I/O VCC Test Circuit and Timing
http://onsemi.com
6
NLSX3014
VCC R1 CL RL 2xVCC OPEN
PULSE GENERATOR RT
DUT
Test tPZH, tPHZ tPZL, tPLZ
Switch Open 2 x VCC
CL = 15 pF or equivalent (Includes jig and probe capacitance) RL = R1 = 50 kW or equivalent RT = ZOUT of pulse generator (typically 50 W)
Figure 5. Test Circuit for Enable/Disable Time Measurement
tR Input tPLH Output 90% 50% 10% 90% 50% 10% tR tPHL tF 50% VL GND HIGH IMPEDANCE 10% 90% VOL VOH HIGH IMPEDANCE
VCC GND
EN
tPZL Output 50% tPZH Output 50%
tPLZ
tF
tPHZ
Figure 6. Timing Definitions for Propagation Delays and Enable/Disable Measurement
http://onsemi.com
7
NLSX3014
TEST CONDITIONS
1. TA = +25C, 2. Input Applied to 1 channel, the other 3 inputs are grounded, 3. CLoad = 15 pF 7 6 5 ICC (mA) 4 3 2 1 0 0 0 1 5 10 25 50 0 1 5 10 25 50 FREQUENCY (MHz) FREQUENCY (MHz) 2 VCC = 3.3 V, VL = 2.5 V VCC = 2.8 V, VL = 1.8 V ICC (mA) 1.5 VCC = 2.8 V, VL = 1.8 V 1 VCC = 3.3 V, VL = 2.5 V 2.5
Figure 7. ICC vs. Frequency (Input = I/O VCC, Output = I/O VL)
Figure 8. IL vs. Frequency (Input = I/O VCC, Output = I/O VL)
5 4 VCC = 3.3 V, VL = 2.5 V ICC (mA) IL (mA) 3 2 1 0 VCC = 2.8 V, VL = 1.8 V
700 600 500 400 300 200 100 0 VCC = 2.8 V, VL = 1.8 V VCC = 3.3 V, VL = 2.5 V
0
1
5
10
25
50
0
1
5
10
25
50
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 9. ICC vs. Frequency (Input = I/O VL, Output =I/O VCC)
Figure 10. IL vs. Frequency (Input = I/O VL, Output = I/O VCC)
http://onsemi.com
8
NLSX3014
IMPORTANT APPLICATIONS INFORMATION
Level Translator Architecture
The NLSX3014 auto sense translator provides bi-directional voltage level shifting to transfer data in multiple supply voltage systems. This device has two supply voltages, VL and VCC, which set the logic levels on the input and output sides of the translator. When used to transfer data from the VL to the VCC ports, input signals referenced to the VL supply are translated to output signals with a logic level matched to VCC. In a similar manner, the VCC to VL translation shifts input signals with a logic level compatible to VCC to an output signal matched to VL. The NLSX3014 consists of four bi-directional channels that independently determine the direction of the data flow without requiring a directional pin. The one-shot circuits are used to detect the rising or falling input signals. In addition, the one shots decrease the rise and fall time of the output signal for high-to-low and low-to-high transitions.
Input Driver Requirements
is referenced to the VL supply and has Over-Voltage Tolerant (OVT) protection.
Uni-Directional versus Bi-Directional Translation
The NLSX3014 can function as a non-inverting uni-directional translator. One advantage of using the translator as a uni-directional device is that each I/O pin can be configured as either an input or output. The configurable input or output feature is especially useful in applications such as SPI that use multiple uni-directional I/O lines to send data to and from a device. The flexible I/O port of the auto sense translator simplifies the trace connections on the PCB.
Power Supply Guidelines
For proper operation, the input driver to the auto sense translator should be capable of driving 2.0 mA of peak output current.
Output Load Requirements
The NLSX3014 is designed to drive CMOS inputs. Resistive pullup or pulldown loads of less than 50 kW should not be used with this device. The NLSX3373 or NLSX3378 open-drain auto sense translators are alternate translator options for an application such as the I2C bus that requires pullup resistors.
Enable Input (EN)
The NLSX3014 has an Enable pin (EN) that provides tri-state operation at the I/O pins. Driving the Enable pin to a low logic level minimizes the power consumption of the device and drives the I/O VCC and I/O VL pins to a high impedance state. Normal translation operation occurs when the EN pin is equal to a logic high signal. The EN pin
ORDERING INFORMATION
Device NLSX3014MUTAG Package UQFN12 (Pb-Free)
It is recommended that the VL supply should be less than or equal to the value of the VCC minus 0.4 V. The sequencing of the power supplies will not damage the device during the power up operation; however, the current consumption of the device will increase if VL exceeds VCC minus 0.4 V. The Enable (EN) pin can be used to provide power savings. Both I/O ports are tri-stated and in low power consumption state if the EN input equals 0 V. The enable pin should be used to enter the low current tri-state mode, rather than setting either the VL or VCC supplies to 0 V. The NLSX3014 will not be damaged if either VL or VCC is equal to 0 V while the other supply voltage is at a nominal operating value; however, the operation of the translator cannot be guaranteed during single supply operation. For optimal performance, 0.01 to 0.1 mF decoupling capacitors should be used on the VL and VCC power supply pins. Ceramic capacitors are a good design choice to filter and bypass any noise signals on the power supply voltage lines to the ground plane of the PCB. The noise immunity will be maximized by placing the capacitors as close as possible to the supply and ground pins, along with minimizing the PCB connection traces.
Shipping 3000 / Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
9
NLSX3014
PACKAGE DIMENSIONS
UQFN12 1.7x2.0, 0.4P CASE 523AE-01 ISSUE A
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 MM FROM TERMINAL TIP. 4. MOLD FLASH ALLOWED ON TERMINALS ALONG EDGE OF PACKAGE. FLASH 0.03 MAX ON BOTTOM SURFACE OF TERMINALS. 5. DETAIL A SHOWS OPTIONAL CONSTRUCTION FOR TERMINALS. DIM A A1 A3 b D E e K L L1 L2 MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.127 REF 0.15 0.25 1.70 BSC 2.00 BSC 0.40 BSC 0.20 ---0.45 0.55 0.00 0.03 0.15 REF
D
AB L1
2X 2X
0.10 C 0.10 C
0.05 C
12X
0.05 C A3
8X
K
5 7
DETAIL A
1 12X
L L2
BOTTOM VIEW
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your loca Sales Representative
II II
TOP VIEW A A1 SIDE VIEW e
11
PIN 1 REFERENCE
E
DETAIL A
NOTE 5
DETAIL B OPTIONAL CONSTRUCTION
DETAIL B
C
SEATING PLANE
MOUNTING FOOTPRINT SOLDERMASK DEFINED
2.00
12X
b 0.10 0.05
M M
CAB C
NOTE 3
1 0.32 2.30
11X
0.40 PITCH
0.22
12X
0.69
DIMENSIONS: MILLIMETERS
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
10
NLSX3014/D

▲Up To Search▲

Price & Availability of NLSX3014

	To Download NLSX3014 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .